Use ‘em if You Got ‘em?

I recently did FOH and monitors for a rock band in a small (250 seat), historic, municipal auditorium. It was a four-piece group: two guitars, bass, and drums along with three vocals. I’d never worked that room before, which meant a lot of new things for me to figure out. It would be my first time out with the Behringer X32 digital mixer along with a few other firsts. One of the reasons I took the job was that the director of the facility is a big proponent of low volume shows and there had been some discussions about keeping it small and quiet from past show experiences. The room acoustics weren’t great, but they weren’t terrible either. The auditorium’s equipment was decent and so, it turned out, was the band.

Mostly because the previous house engineer had a show “scene” from the last year’s show, I sort of went with his stage setup. I mic’d both guitar amps and ran a DI from the bass. I setup two overhead mics and a kick mic on the kit, abandoning the previous session’s snare and tom mics. In the end, I used about 16 channels for the 4-piece band. We did a quick sound check, first with the FOH system for me followed by ringing out the monitors. The guitar player at far stage right complained that he couldn’t hear the bass (who was setup far stage left) and I ran up the bass in his monitor to the point it was cancelling the output from the bass player’s amp and overwhelming the FOH bass output. He still couldn’t hear it, so I dialed it back to where it interfered less with the FOH sound. He was the old guy in the group and the loudest amp on stage, so I made the assumption that he was stereotypically R&R deaf. It’s also possible that there was a LF phase-cancellation problem on the stage.

The facility manager complained about the volume during the sound check and I got the bass player and lead guitarist to dial it back a bit. The rhythm guitarist made a show of fake adjusting his amp, but it was obvious that he didn’t intend to comply with the venue’s volume limits. I didn’t bring an SPL meter because I assumed the venue had one, based on the fact that there is a loudness restriction there. I’d guess the show was somewhere between the low and mid-90dBSPL territory.

I started the show with instrument volumes very low to see where the players would go once they got into the performance. Pretty quickly, I pulled the rhythm guitar, bass, and kit out of the mix. I tried to mix the lead guitar signal, up during solos and down the rest of the time, but his signal was mostly so distorted (It was a Neil Young cover band after all.) that my addition to the distortion fog only served to screw up the rest of the mix. That was really demonstrated during a song where he solo’d without his distortion pedals and the guitar lept out of the mix all by itself. That clue’d me into the fact that, if I wanted to hear his solo guitar I needed to band-limit it drastically. I low-passed the lead guitar at about 3kHz and high-passed it at 300Hz, which gave me a signal that I could work with.

In the end, I found myself with faders up on three vocal mics, a DI’d acoustic guitar, and everything else fully attenuated or close to it. I had one moment, about 30 seconds long, where I brought the kit up noticably and I flailed away for most of the first set trying to figure out how to get the lead guitar prominently into the mix. I should have taken a picture of the console: two-to-three faders up and the rest all the way out. All that equipment, all that processing power, and no real need for me to be there for most of the show.

If I’d have just setup up three mics and one DI, I’d have had more sound than the room and audience needed. Even from the monitor standpoint, no one asked for drums in their monitors. The drummer wanted a little lead guitar and bass in his mix. I already talked about the rhythm guitarist’s problems. The end result, from front of house, of the monitor mix was that the bass was constantly overpowering the rest of the band; even though I didn’t put any of the bass in the FOH mix. I nagged the bass player to turn down during the break and he claimed that he didn’t change anything from the sound check. In retrospect, I should have believed him because I was what changed when I tried to make the drummer and rhythm guitarist happy with bass blast in their monitors.

It’s a serious temptation to use ‘em if you got ‘em. You spent all that time and energy setting up mics and running cables for no good reason other than the wild hope that you might actually get to mix a show. In my case, 12 of the 16 lines and mics I’d run were unnecessary. I suspect if I did this on a regular basis, I’d be inclined to give myself more faders to play with just out of boredom. The volume would creep up, the sound quality would disintegrate, but I’d be occupied. It’s something to keep in mind if mixing live sound is going to be your life. You are often unnecessary.